标题: （非原创）惠普C3110, C3210 or C3310系列机器，墨水故障解决 [打印本页] 作者: yangtzs 时间: 2010-10-13 22:13 标题: （非原创）惠普C3110, C3210 or C3310系列机器，墨水故障解决 Are you experiencing the ink system failure on your printer? The error is caused by air getting in the ink tubes feeding the system. This is normally cause by refilled cartridges but can be caused by any cartridge that goes very low on ink and then tries to reload ink. This reset procedure does have to be performed with a full cartridge installed. The following reset procedure will correct the issue by purging the ink tubes and flushing any air trapped in them. 1 A6 g8 k: k: J6 D( W( F B- E# k* p0 \) c有经历过墨水系统故障吗，墨水系统故障是因为空气进入了墨水供应系统管道。经常产生于加过墨的墨盒，也会产生于任何墨水量少的墨盒中。这个复位的步骤只能使用新的满的墨盒。因为可以排出管道中的空气，解决问题。 . Q3 ~: X A& V2 `( j$ iThis sequence works if you have a C3110, C3210 or C3310 series printer. This reset procedure should also work on any printer without FAX capabilities. 0 z- l4 y P, {2 R& H8 A+ A
以下步骤是专门对C3110, C3210 or C3310 系列打印机的，也可以用于那些没有传真功能的打印机。, W9 x+ O! R; u; ?8 G4 p
o+ @ n# H/ cPlease perform the following steps in order:% z9 v2 ^% p8 U \$ N ^8 v
1. Make sure you have new cartridges in the printer so that it can reset. {1 `1 J7 [4 k1 [1 d
保证机器中的墨盒是新的，这样才可以重置( ~' n& B# f, c E# ^# K. L
2. Press down the OK and Cancel buttons down at the same time and turn the printer off.! a, o. |6 l7 ^0 K4 a
同时按ok和取消键# S6 |) Z/ V5 o: d1 R
3. Keep holding the buttons down until the printer turns off. ; K: H- j6 N3 Y( t- J; A, R一直按着，直到机器自己关机 8 V: K. L( e, d( H( b: m4. Release the buttons.: {7 o D T. D) d: t% R6 G
关机后松开按扭 k: M! N& T, O( f: g6 f; P5. Now turn the printer on while pressing the OK and Cancel buttons. It should cycle a bit then turn back off.) S3 R9 Q7 V0 s2 e& J2 L
一会后，再在同时按着ok键和取消键的时候开机，开机后保持按住这两个键，等待它关机。 ; V6 K9 x8 X, y$ d" g- F D4 a6. Turn the unit on again. # C0 u. k, ~0 ~3 j" ~6 L再开机- P6 U" z( G! z/ W! W/ P; _/ p
7. After the second time off/on the printer will recalibrate the ink cartridges, this will take about 5 minutes. ) B. @6 V% J/ o/ x- N再第二次关、开机后，机器会重新校准墨盒，这个过程5分钟左右。 - u& Y" ~3 |# O$ X$ C a8 [( G7 J* T
8. After calibration it should be online ready to print. Print a test page to verify operation.- U8 d, O6 W6 d/ h! K
重新校准后，应该可以打印，打印一个测试页以检查效果。 ; P! f7 s6 W0 K- d4 z$ ~You should be back up and running. If this procedure does not solve the problem then remove the cover from the printer and check the small white gear on the end of the ink pump. The gear can come off after heavy use, just push it back on and then redo the reset precedure as described above.4 x2 B9 h3 _+ q6 o
如果不成功，打开机器盖子，检查墨水泵端部的白色的小齿轮，小齿轮有可能脱开了，把它按回去，再重新上面的步骤。( v" G) k& _5 B) G9 d7 s1 `
原文http://www.ccl-la.com/blog/index.php/hp-photosmart-ink-system-failure-2/1 W' p% q S/ W' T5 X/ b
, s* T! q/ o" Y6 z, A/ |
[ 本帖最后由 yangtzs 于 2010-10-18 17:17 编辑 ]作者: dxqysq 时间: 2010-10-15 09:50
提示: 作者被禁止或删除 内容自动屏蔽作者: yangtzs 时间: 2010-10-18 17:13
在第一步过程中，有朋友的机器没用新墨盒，也能重置。作者: wangzhenhan 时间: 2010-10-21 22:40
学习呀，有用！！