EPSON7600 求助~~~~~！

arui239 · 发表于 2005-12-7 20:20:00

<

>各位大虾：小弟有一台7600 今早开机面板显示00010005 指示灯全部都在闪。
<

>电话咨询EPSON说是硬件问题，不知各位大虾谁遇到过此类问题，请指教！
<

>超级急啊！！！！！！！！！！！！请加QQ：122715174 谢谢啊！！！！[em03][em03][em03][em03][em03][em03][em03][em06][em06][em06][em06][em06][em06]

yj · 发表于 2005-12-7 21:26:00

<

>有无不正常撞击的声音?

arui239 · 发表于 2005-12-7 22:15:00

<

>有。。。。不正常的咯噔声！

haijiekeji · 发表于 2006-1-8 01:06:00

<

>我也有这样的报错,我认为是光栅的事,你找一个干净的东西再找一些干净的水擦一下光栅吧
<

>我的电话:13475168018

haijiekeji · 发表于 2006-1-8 01:08:00

<

>还有可能是纸敢光的事，打个小东西擦一下纸下面的小洞，
<

>再不行打１３４７５１６８０１８找我，
<

>我有３台打印机，

mwmpop · 发表于 2006-1-9 06:14:00

<

>厂家内部维修资料:----可以解决99%的问题
<

>Error Code Description Refer to
<

>00010003 PF motor in-position time-out p.136 00010004 CR motor encoder check error p.137 00010005 CR motor out of step p.137 00010006 CR motor overcurrent p.138 00010007 CR motor in-position time-out p.138
<

>马达错位了
<

>按以下步骤调整就可以了
3.2.4.7 CR motor out of step (00010005) 􀂆 Explanation: During CR Motor operation, there may be a case where the encoder pulse signal within the specified range is not input within a specified period of time or the pulse width is extremely long. In such a case, the CR Motor is judged to be out-of-step, so that this message is displayed and the printer stops operating. 􀂆 Cause of trouble: • The error counter has reached the out-of-step pulse count because of impossible movement of the carriage, bumping of the carriage or dirty timing fence. • Defective motor. 􀂆 Points to be checked: 1. The CR Encoder and the T Fence must be free from dust and dirt or any other foreign matters. 2. The CR Timing Belt must be free from any defects and the belt must be in proper tension. 3. The carriage must slide smoothly, free from undue load. 4. Measure the resistance value of the CR Motor. (5.8Ω) 5. Execute encoder checking by “5.2.2.4 Encoder ”(p225) in the selfdiagnostics menu. 6. All the harness must be connected properly and free from short circuit or broken wire. 7. Check the carriage home position sensor. 􀂆 Remedy: • Replace the CR Motor ASSY (p.180). (Refer to “CR Timing Belt Tension Adjustment” (p.263)) • Replace the MAIN Board (C472 MAIN) (p.207). • Replace the CR_HP Sensor ASSY (p.183). • Replace the CR Encoder Sensor ASSY (p.178). (Refer to “CR Encoder Sensor Mounting Position Adjustment” (p.268)) • Replace the CR Encoder Scale (Timing Fence) (p.184). • Check to see if the timing fence for detection of the encoder pulse is not installed correctly. • Check for dirt, paper dust or damage to the timing fence

zhang1981 · 发表于 2006-1-11 00:09:00

兰州王杰 · 发表于 2006-1-13 02:20:00

哪为高手能把6楼的翻译一下。

daima · 发表于 2006-2-5 04:41:00

<

>我遇见过，是图中所示的地方错位了，复原即可。
<

><a href="http://bbs.inknet.cn/dispbbs.asp?boardid=28&id=24646" target="_blank" >http://bbs.inknet.cn/dispbbs.asp?boardid=28&id=24646</A>

		自动登录	找回密码
密码			注册